http://www.jeffmirisola.com/2008/09/lets-talk-sheetmetal/ SolidWorks Tips, Tricks and Partner Reviews Thu, 15 Dec 2011 02:20:17 +0000 hourly 1 http://wordpress.org/?v=3.2.1 http://www.jeffmirisola.com/2008/09/lets-talk-sheetmetal/comment-page-1/#comment-325 Let’s Talk Sheetmetal | Jeff’s Tool Shed Fri, 01 May 2009 21:16:13 +0000 http://jeffsblog.solidworksheard.com/?p=149#comment-325 [...] Keep Reading: Let’s Talk Sheetmetal | Jeff’s Tool Shed. [...]

]]> http://www.jeffmirisola.com/2008/09/lets-talk-sheetmetal/comment-page-1/#comment-188 Brian Wed, 03 Dec 2008 14:33:44 +0000 http://jeffsblog.solidworksheard.com/?p=149#comment-188 Jeff, I agree, using the unfold/fold is the easiest way of putting holes in a bend. 97% of my work is sheet metal so I was just wondering what you was using the unfold/fold for other than putting cuts and holes in bends. Later, Brian Jeff,
I agree, using the unfold/fold is the easiest way of putting holes in a bend. 97% of my work is sheet metal so I was just wondering what you was using the unfold/fold for other than putting cuts and holes in bends.
Later,
Brian

]]> http://www.jeffmirisola.com/2008/09/lets-talk-sheetmetal/comment-page-1/#comment-1423 Brian Wed, 03 Dec 2008 14:33:00 +0000 http://jeffsblog.solidworksheard.com/?p=149#comment-1423 Jeff, I agree, using the unfold/fold is the easiest way of putting holes in a bend. 97% of my work is sheet metal so I was just wondering what you was using the unfold/fold for other than putting cuts and holes in bends. Later, Brian Jeff,
I agree, using the unfold/fold is the easiest way of putting holes in a bend. 97% of my work is sheet metal so I was just wondering what you was using the unfold/fold for other than putting cuts and holes in bends.
Later,
Brian

]]> http://www.jeffmirisola.com/2008/09/lets-talk-sheetmetal/comment-page-1/#comment-187 Jeff Mirisola Wed, 03 Dec 2008 00:41:54 +0000 http://jeffsblog.solidworksheard.com/?p=149#comment-187 Brian, I do use the hole wizard when applicable. Using unfold/fold depends on where and when the holes are applied in process. Best example is if a hole needs to straddle a bend. Brian,
I do use the hole wizard when applicable. Using unfold/fold depends on where and when the holes are applied in process. Best example is if a hole needs to straddle a bend.

]]> http://www.jeffmirisola.com/2008/09/lets-talk-sheetmetal/comment-page-1/#comment-1422 Jeff Mirisola Wed, 03 Dec 2008 00:41:00 +0000 http://jeffsblog.solidworksheard.com/?p=149#comment-1422 Brian, I do use the hole wizard when applicable. Using unfold/fold depends on where and when the holes are applied in process. Best example is if a hole needs to straddle a bend. Brian,
I do use the hole wizard when applicable. Using unfold/fold depends on where and when the holes are applied in process. Best example is if a hole needs to straddle a bend.

]]> http://www.jeffmirisola.com/2008/09/lets-talk-sheetmetal/comment-page-1/#comment-186 Brian Wed, 03 Dec 2008 00:01:29 +0000 http://jeffsblog.solidworksheard.com/?p=149#comment-186 Why don't you put the holes in the sheetmetal part using the hole wizard while it's in the bent state? I use this method most of the time. Just curious. Brian Why don’t you put the holes in the sheetmetal part using the hole wizard while it’s in the bent state? I use this method most of the time. Just curious.
Brian

]]> http://www.jeffmirisola.com/2008/09/lets-talk-sheetmetal/comment-page-1/#comment-1421 Brian Wed, 03 Dec 2008 00:01:00 +0000 http://jeffsblog.solidworksheard.com/?p=149#comment-1421 Why don't you put the holes in the sheetmetal part using the hole wizard while it's in the bent state? I use this method most of the time. Just curious. Brian Why don’t you put the holes in the sheetmetal part using the hole wizard while it’s in the bent state? I use this method most of the time. Just curious.
Brian

]]>